June 12, 1967SB-101 Bulletin No:SSB Transceiver SB-101-1D Driver Oscillates on 40 Meters Remove C-924 [.02 disc capacitor] from across 150K ohm resistor & delete from circuit. ------------------------------------------------------------------------------------------------------------------ November 1, 1967SB-101 Bulletin No:SSB TransceiverSB-101-2D Switch Action Improvement DELETE: (2) 253-67 (2) WASHER, .186OD, .054 THICK (1 EA FOR 100-445) ADD: (2) C253-67 (1) " " " " " (FOR 100-445)ADD: (2) B255-79 (1)SPACER, 1/8 SHOULDER, THREADED ADD: (2) A263-7 (1)FOOT, FELT, 1/8" THICK DELETE:(4) 266-91 (1)ACTUATOR, SLIDE SWITCH ADD: (4) 266-97 (1) " " " " ----------------------------------------------------------------------------------------------------------------- NOVEMBER 1, 1967SB-101 Bulletin No:SSB TransceiverSB-101-3D Improper Tuning Delete: [2] 26-109 [2] Variable Capacitor, 2 Sect. P.C. Mtg Add: [2] 27-122 [2] Variable Capacitor, 2 Sect. P.C. Mtg Delete: [4] 85-131-1 [1] PC Board, RF Driver Mixer [85-131 Screened 605-1225] Add: [4] 85-131-2 [1] PC Board, RF Driver Mixer [85-131 Screened605-1616] Reason for change: To correct tuning trouble. ------------------------------------------------------------------------------------------------------------------- APRIL 18, 1968SB-101 Bulletin No:SSB TransceiverSB-101-4D Improper Tuning on 40Meters Description of Change: DELETE: (2) B21-31 (50) CAPACITOR, DISC .02 MFD Z5U ADD : (2) B21-31 (49) " " " " "DELETE: (4) 85-131-1 (1) PC BOARD, RF DRIVER MIXER ADD : (4) 85-131-1 (1) " " " " REMOVE: C-424 installed across R-401 NOTE: SBM-100-1 called for the installation of this capacitor on SB-100 units. This capacitor should now be removed. -------------------------------------------------------------------------------------------------------------------- June 3, 1968SB-101 Bulletin No:SSB TranceiverSB-101-5D Grounding Problems on Tranceivers A quality of factory wired transceivers have been shipped with loose rivets both at the rear phono sockets & at the final tube sockets. This is causing a serious grounding problem. Corrective recommendations are shown on the attached sheet: [[[[[[[[[[[[[NOTE: IF MY INTERPRETATION IS NOT CLEAR - PSE LET MEKNOW]]]]]]]]] Illustration shows the installation of a ground buss for the rear panel phono sockets. It also states that if the final tube socket rivets are loose, they should be drilled out & eplaced with 6-32 hardware. ------------------------------------------------------------------------------------------------------------------- November 25,1970 SB-101 Bulletin No:SSB TransceiverSB-101-1 MeterZeroing Original 10-147 control tolerance not sufficient to allow zeroing in all units. This part is being respecified to a closer tolerance. In the meantime, any field problems requarding zeroing of the meter can be corrected as follows:Change: R-107 from 100K Ohm to 82K Ohm (1-159). ------------------------------------------------------------------------------------------------------------------- September 14, 1972SB-101 Bulletin No:SSB Transceiver SB-101-2 Repeated Heterodyne Oscillator Failure Change: R-212 from 220 Ohm to 330 Ohm 1/2 Watt resister (1-4). ------------------------------------------------------------------------------------------------------------------ May 23, 1974SB-101Bulletin No: SSB TransceiverSB-101-3 SB & HW Series Audio Amplifier & VOX Circuit Trouble Shooting Guide It is assumed that the basic steps such as making DC voltage measurement, checking tubes & reviewing the soldering have been completed. The following information was compiled from the above transceivers in the 80M LSB position. The mike level control was at the 9:00 o'clockpoisition. AC signal voltages are listed below. These voltages were measured from the microphone connector through the VOX circuit. All measurements were made with a VTVM. A microphone or audio generator for .1V @ 1KHZ can be used as the signal source.Mike Connector Lug 1 .1VAC Pin 2 of V1 .02VAC Pin 6 of V1 10-15VAC Pin 6 Level Control 10-15VAC Pin 5 Level Control .5VAC Pin 9 of V1 .2VAC Pin 8 of V1 .1 - .3VAC Center Arm of VOX Sensitivity Control 5-15VAC Pin 7 of V17 5-10VAC Pin 6 of V17 40-50VAC Junction of C211-D201 40-50VAC Pin 9 of V12 9-15VAC By tracing the AC signal from stage to stage the point of trouble can be isolated & steps taken to correct it.POSSIBLE TROUBLE AREAS - Check each of the shielded cables for a possible open or poorly grounded shield.- Check for continuity through each of the shielded cables. - Check for a proper ground at the mike control level. - If the frequency response of the audio stage is not within specifications check the values & installation of C1, C2, C3 & C9. - A change in VOX delay after operating for a period of time can be caused by leakage in diode D201. The other possibility is a change in value of capacitor C213. Either component could experience a change in operation characteristics due to heat. ------------------------------------------------------------------------------------------------------------------ May 23, 1974SB-101 Bulletin No:SSB TransceiverSB-101-4 Diode Leakage in The SB-100, SB-101, HW-101 The silicon diodes used in the SB100 & SB101 are standard power diodes rated at 500PIV & 750MA. For each condition described, the diodes should be replaced with an equal value to maintain proper opration. 1. Diodes D902 & D903, when leaky, will have an effect on ALC indication. The ALC indication will be normal for the first half hour to an hour. Then the meter indication will start dropping off until there is very little indication. 2. D101, when leaky or defective, will cause slow or no receiver recovery after transmitting for any period of time. 3. D905, under leaky conditions, will cause very slow or no receiver recovery and false meter indications. The meter will kick up scale & slowly drift down to zero. 4. D201 will result in a decrease in VOX sensitivity to the point where the VOX circuit will not be activated. It can also result in increasing VOX delay, causing the relay to stay in the transmit condition. ------------------------------------------------------------------------------------------------------------------- May 23, 1974SB-101 Bulletin No: SSB Transceiver SB-101-5 SB & HW Series Instability & Corrective Information Instability -- Troubleshooting We suggest you check for each of the following possible causes: 1. Intermittent, rosin or cold solder joints. 2. Loose hardware at the tube sockets, terminal strips, circuit boards, shields and rear panel sockets. 3. Poor lead dress at tube sockets V8 & V9. The component leads must be short as possible. 4. Check C925 (Final tune capacitor) to be sure it is isolated from the tuning shaft. This is to prevent RF from traveling on the shaft to the front panel. 5. Check all edges of the final enclosures for proper grounding to the main chassis. 6. Check the hardware for the side rails to be sure a good ground is being provided. 7. Be sure that all the ground clips on the coil cover are making good contact with the switch shields. 8. Check the soldering of the switch shields to the center pins of tube sockets V6, V7, V10 & V11. 9. Check the ground leads from the switch board & shields, to be sure they are going to ground foil & not to the preselector capacitor foil pods on the RF driver board. 10. Check for broken or shorted pigtails on each of the shielded cables in the unit.11. Check RFC801 & L901 for any signs of deterioration or physical damage, (burn spots). If apparent replace the part. 12. Improper adjustment of the Het. Osc. coils could cause impropermixing action, resulting in the final operating at a different frequency appearing as instability. 13. Change driver & final tubes then reneutralize per manualinstructions. 14. Check driver tube shield to be sure that it has a good ground contact with the socket spring clip. 15. Check for a good ground between the front panel & chassis. 16. Check the SWR of the antenna system at the frequency of operation. Should be below 2:1. 17. Check the antenna coax for leakage, poor connectors & broken shield connections.18. Is the transmitter properly grounded? 19. Be sure all shields & tube shields are installed. 20. Realign using a properly terminated 50 ohm non-reactive dummy load. NOTE: This does not include a light bulb. 21. Check for normal Het. Osc. test-point voltage. 22. Check for proper LMO injection voltage 1.0-1.5 VRF. 23. Check for a high AC ripple content in the LV-B+, HV-B+ and bias voltages from the power supply. 24. Check to be sure that the shafts do not touch each other in theinsulated coupling, and that the set screws do not touch the PA shield. 25. Check to be sure that the PA tune shaft turns the variable capacitor & is not slipping in the insulated coupling. -------------------------------------------------------------------------------------------------------------------- May 23, 1974SB-101 Bulletin No. SSB Transceiver SB-101-6 Alternate Method of Neutralizing The Final Amplifiers 1. Disconect final plates & screen grid.***2. Turn unit on. 3. Rotate the BAND switch to 28.5. 4. Place the VTVM RF probe in the ANTENNA connector.** 5. Set the FUNCTION switch to TUNE. 6. Rotate the LEVEL control fully clockwise. 7. Adjust the PRESELECTOR control for a maximum reading on the VTVM. 8. Adjust the FINAL control for a maximum indication on the VTVM, with the LOAD control set at the 50 ohm position. 9. Using an insulated screwdriver, adjust neutralizing capacitor for a MINIMUM indication on the VTVM. 10. Readjust the neutralizing capacitor for a minimum indication on theVTVM. 11. Turn the FUNCTION switch to the off position. 12. Discharge high voltage power supply capacitors. 13. Reconnect final plates & screen grid.**VTVM & RF probe will be needed. ***To remove screen voltage in SB-100, SB-101, HW-100 & HW-101 disconnect R920 (100 ohm resistor) from buss wire between pins of V8 & V9. In the SB-102 removal of accessory plug is all that's required. To remove high voltage in SB-100, SB-101 & SB-102 disconnect red wire at lug 4 (in Sb-100 lug 3) of terminal strip BK that goes to grommet BL. In HW100 & HW101 disconnect red wire going to lug 1 of RF choke in final cage. NOTE: Take adequate steps to eliminate any possible contact with B+ or B+ shorts to chassis after disconnecting wire & resistor. -------------------------------------------------------------------------------------------------------------------- December 18, 1974SB-101 Bulletin No. SSB Transceiver SB-101-7 Oscillations or Low Drive Loose boards cause sporatic self oscillations & unstable RF conditions, particularly at the high [15 & 10 meter] bands. The comb brackets which ahve been used are aluminum & could not be soldered. Steel brackets are now available [Part No: 204-2096] & should be used whenever encountered in the field. Both the switch shields & the driver boards should be soldered to these brackets. This change helps to increase grid drive as well as increase stability. -------------------------------------------------------------------------------------------------------------------- May 2, 1975SB-101 Bulletin No. SSB Transceiver SB-101-8 Self Oscillations Occurring After Installation of Steel Comb Brackets It has been found that in a number of units, self oscillations are still occurring after installation of both sets of comb brackets [Part No: 204-2096]. To correct the condition, the screws around the RF driver board must be tightened securely. Also, the lockwashers between the circuit board & chassis must be installed, otherwise a good ground is not assured. Retightening screws which are already snug will also cause these oscillations to disappear in units where it is a problem. -------------------------------------------------------------------------------------------------------------------- March 29, 1976SB-101 Bulletin No:SSB Transceiver SB-101-9 S-Meter Drift To bring the meter drift to an acceptable level, install the following: CHANGE: R107 from 100K Ohm 1/2 Watt to 100K 1 Watt [PN 1-28-1] This makes the voltage divider string more stable with temperature changes caused by internal heating. This change will be made in future production runs. ------------------------------------------------------------------------------------------------------------------ November 15, 1976SB-101 Bulletin No: SSB Transceiver SB-101-10 Low Receiver Sensistivity Note: Sensitivity of the unit is worse on the higher frequencies [15] & [10] meters.Cure: Diode D907 may be in backwards or banded backwards. ------------------------------------------------------------------------------------------------------------------ September 27, 1977 SB-101 Bulletin No: SSB Transceiver SB-101-11 Transceiver Oscillates in Transmit with Mic Keyed + + + + Information not yet available + + + + -------------------------------------------------------------------------------------------------------------------- February 22, 1978SB-101 Bulletin No:SSB Transceiver SB-101-12 Tuning Erratic Some of the earlier LMOS can be opened up for service, such as cleaning the wiper contacts on the tuning cap when tuning becomes erratic. Some of these units have fiber washers between the frame of the tuning capacitor and the worm gear assembly. Intermittant contact between the teeth of the gears can change the ground path for the tuning cap and also cause erratic tuning. Simply replacing a fiber washer with a metal washer will give good connection between the tuning cap frame and the worm gear assembly to eliminate this problem. ------------------------------------------------------------------------------------------------------------------ June 5, 1978SB-101Bulletin No:SSB Transceiver SB-101-13 Relays Remain Energized After Transmit Condition After keying the transceiver with PTT for thirty to forty seconds, a positive voltage in